Generic

18pF/0.018nF/0.000018uF 180 Ceramic Capacitor (Pack of 20)The ceramic capacitor is a non-electrolytic type capacitor used in different electronic applications.Features of 18pF/0.018nF/0.000018uF 180 Ceramic Capacitor Capacitance: 18pF/0.018nF/0.000018uFCode: 180Type: Ceramic Capacitor..

An aluminum electrolytic capacitor, often only called an electrolytic capacitor, uses aluminum metal as one electrode, covered with a very thin layer of aluminum oxide as dielectric, and which has an the electrolyte as its second electrode.Aluminum electrolytic capacitors are typically used in power..

This is a variable resistor breakout module for students and they can change the resistance and experiment more on circuit easily.Features of Variable Resistor Breakout:Easy to use.Ease of interfacing.Long life.Applications of Variable Resistor Breakout:It is used in Arduino/AVR/ARM/PIC/ projects.No..

An aluminum electrolytic capacitor, often only called an electrolytic capacitor, uses aluminum metal as one electrode, covered with a very thin layer of aluminum oxide as dielectric, and which has an the electrolyte as its second electrode.Aluminum electrolytic capacitors are typically used in power..

An aluminum electrolytic capacitor, often only called an electrolytic capacitor, uses aluminum metal as one electrode, covered with a very thin layer of aluminum oxide as dielectric, and which has an the electrolyte as its second electrode.Aluminum electrolytic capacitors are typically used in power..

25mmx18mm Single Turn Potentiometer Knob Rotary Switch Black Cap for 6.5mm shaft :This is a Potentiometer Knob Rotary Switch Cap with a 6.5mm inner diameter. It easily fits with potentiometer, Rotary switches used in various electronic devices. The knob makes it very easy to rotate and vary the swit..

This ATMEGA 168PA microcontroller is a 8 bit AVR RISC based microcontroller used in Arduino.Features of ATmega168PA AU Atmel Arduino IC:Operating Voltage: 1.8 to 5.5 V.Flash memory: 16 Kb.EEPROM: 512 Byte.SRAM: 1K.I/O pin: 32 pin.USART protocol interface.I2C protocol interface.SPI protocol interface..

This product is an angular rate sensor that uses the phenomenon of Coriolis force, which is generated when a rotational angular rate is applied to the vibrator.Features of ENC 03RC R Murata Gyroscope:Ultra-small and ultra-lightweight.Quick response.Low driving voltage, low current consumption.Lead t..

The Motor driver is based on the diode basis, which is a Half-bridge driver designed to drive inductive loads such as relays, solenoids, DC and stepping motors. It lets you drive two DC motors with your Robomart Arduino board, controlling the speed and direction of each one independently. You can al..

The ULN2803 Stepper Motor driver is ideal for driving a stepper motor through Arduino or any other platform.Specification of ULN2803 Stepper Motor Driver Board:500mA drain per channel.Up to 50V Output Voltage.Output Clamp Diodes.Medium Power Stepper Motor Application.Applications of ULN2803 Stepper ..

79M09 is a voltage regulator integrated circuit. It is a member of 79xx series of fixed linear voltage regulator ICs. The voltage source in a circuit may have fluctuations and would not give the fixed voltage output. The voltage regulator IC maintains the output voltage at a constant value. The xx i..

The Constant pressure ZXY6005S constant current switching power supply improvement introduced in the original ZXY6005, ZXY6010 power module based on high power, full CNC switching power supply products, the maximum output current of 5A, the voltage and current regulation are coded switch CNC adjustm..

The ESP module is a Smart Connectivity Platform (ESCP) of high performance wireless SOCs, for mobile platform designers, provides unsurpassed ability to embed Wi-Fi capabilities within other systems, at the lowest cost with the greatest functionality.Features of ESP8266 remote serial Port WIFI wirel..

This kit is designed to get you started quickly and easily on your path of learning electronics. Once you've received your starter pack you can start to play with little or no electronics and programming experience. The advanced kit has more components and sensors you need to play compared with the ..

The resistor array is a passive nine-terminal electrical component that serves as eight 1K ohms resistances and one common ground.Features of 1 Kilo Ohm Resistance Array 5 Pin:Type: Array.Resistance - 1K ohm.Power- 1/4 watt.Applications of 1 Kilo Ohm Resistance Array 5 Pin:It is used in Robotics pro..

Introducing the STA401A NPN Darlington Transistor with Built-In Avalanche Diode – your ultimate solution for precision amplification and enhanced protection in electronic circuits. Designed with cutting-edge technology and meticulous craftsmanship, this versatile component empowers your designs with..

ROBOMART makes a low-cost relay board shown above that contains both the relay and the required driver circuit built using a discrete transistor. The relay coils on this relay require around 6VDC. It is easier to drive relays like this that use a lower coil voltage. The relay can switch up to 220VAC..

The single digit Common cathode Seven Segment Display is a light weight easy to use break out module. This single Digit Common cathode Display is compatible with any circuit and any microcontroller module.Features of Single Digit Common Cathode Seven Segment Display:Ease to use.Ease of interfacing.L..

These type of inductors are looking like resistors which used in different applications.Features of 10mH Resistor Shaped Inductor:Inductance: 10 mH.Power: 1 watt.Applications of 10mH Resistor Shaped Inductor:It is used in commercial purposes.Multiple DIY projects.Note: Images shown is only for repre..

The MCF5206 integrated microprocessor combines a Cold Fire processor core with several peripheral functions such as a DRAM controller, timers, general-purpose I/O and serial interfaces, debug module, and system integration. Designed for embedded control applications, the Cold Fire core delivers enha..