Special Offers

This is high quality 12V, 15Amp SMPS intended for industrial use. We use these SMPS for heavy duty robotics applications. They have built in Short circuit, Overload and Over voltage protection. It can withstand input of 1500V AC up to 60 seconds. Output voltage can be adjusted by up to +-10% of the ..

The AVR/8051 USB programmer is an in-circuit programmer for Atmel AVR/8051 controllers. The programmer uses a firmware-only USB driver; no special USB controller is needed. It is complete solution for programming popular AVR/8051 series of micro controllers with ease. This is a USB based programmer...

This driver uses Infineon chips BTS7960 composed of high power drive full H-bridge driver module with thermal over current protection. Double BTS 7960 H-bridge driver circuit, with a strong drive and braking, effectively isolating the microcontroller and motor driver! High current 43A.Features:Doubl..

We are offering quality tested Graphic LCD Display Green 128x64 - JHD make that can display not only alphanumeric data but simple graphics also. Fabricated from advance technology, these LCD's are highly suitable for animations and neat menus. Moreover, our product can handle the 128*64 pixels and c..

GSM/GPRS Modem-RS232 is built with Dual Band GSM/GPRS engine - SIM900Awhich works on frequencies 900/1800 Mhz. The Modem comes with RS232 interface, which allows the user to connect PC as well as microcontroller with RS232 Chip(MAX232). The baud rate is configurable from 9600- 115200 through AT comm..

The CC2530 is TI's second generation ZigBee® / IEEE 802.15.4 RF System-onChip (SoC) for the 2.4 GHz unlicensed ISM band. This chip enables industrial grade applications by offering state-of-the-art selectivity/co-existence, excellent link budget, and low voltage operation. The CC2531 is identical to..

This AVR Parallel Port Programmer can be used for in-system programming for Atmel ISP programmable devices. The programming interface is compatible to STK200 ISP programmer hardware so the users of STK200 can also use the software which can program both the 8051 and AVR series devices.Features of AV..

The AVR Serial Programmer simple COM PORT based AVR at-mega Programmer will allow you to easily transfer hex programs to most ATMEL AVR microcontrollers. It is more reliable than most other simple AVR programmers available out there and can be used without a usb port.Features of AVR Serial Programme..

A 20 x 4 LCD display means it can display 20 characters per line and there are 4 such lines. In this LCD each character is displayed in 5x7 pixel matrix.Features of 20x4 Character LCD Display:Operating Voltage: 5V.Backlight Colour: Green.Horizontal Characters: 20.No. Of lines:4.Supports MCU speeds u..

This is a simple to use, USB to serial base unit for the Digi X Bee line. This unit works with all X Bee modules including the Series 1 and Series 2.5, standard and Pro version. Plug the unit into the X Bee Explorer, attach a mini USB cable, and you will have direct access to the serial and programm..

The 4-Digit 7-Segment Display is a self-contained module containing four 7-segment LED numeric displays. This module is a very simple common cathode display can easily interface with any microcontroller development board.Features of 4 Digit Seven Segment Display Board (Common Cathode):4 multiplexed ..

What are Real-Time Clocks?Real-time clocks (RTC), as the name recommends are clock modules. The DS1307 real-time clock (RTC) IC is an 8 pin device using an I2C interface. The DS1307 is a low-power clock/calendar with 56 bytes of battery backup SRAM. The clock/calendar provides seconds, minutes, hour..

AVR USB programmer is an in-circuit programmer for Atmel AVR controllers. The programmer uses a firmware - only USB driver; no special USB controller is needed.It is complete solution for programming popular AVR series of micro controllers with ease. It can be used with Low Cost ATmega development b..

This kit is designed to get you started quickly and easily on your path of learning electronics. Once you've received your starter pack you can start to play with little or no electronics and programming experience. The advanced kit has more components and sensors you need to play compared with the ..

It is an IR based proximity Sensor Array that provides 5 Bit of Digital output based on the Surface sensed by the sensors. The array is a group of 5 IR sensors which sense precisely the changes and provides a perfectly differentiate input values for constructing an intelligent Robot.Features of Five..

The MPU-6050 sensor module contains an accelerometer and a gyro in a single chip. It is very accurate, as it contains 16-bits analog to digital conversion hardware for each channel. Therefore it captures the x, y, and z channel at the same time. The sensor uses the I2C-bus to interface with the Ardu..

Flexion sensors, (from Latin flexure, 'to bend') also called bend sensors, measure the amount of deflection caused by bending the sensor. There are various ways of sensing deflection, from strain-gauges1) to hall-effect sensors2).Features of Flex Sensor 2.2:Hysteresis/noise neglectible3).Resistance ..

The Raspberry Pi 3 Case for Raspberry Pi 3 Model B B+ only Red/Whiteis a 5-part Enclosure for Raspberry Pi 2 model B, B+, and Raspberry Pi B+. Official case for the Raspberry Pi from the Raspberry Pi Foundation.It has removable Lid for easy access to the camera and display ports, Removable Side Pane..

This kit is designed to get you started quickly and easily on your path of learning electronics. Once you've received your starter pack you can start to play with little or no electronics and programming experience. The advanced kit has more components and sensors you need to play compared with the ..

This arduino motor drive shield allows driving two channel DC motors. It uses a L298N chip which deliveries output current up to 2A each channel. The speed control is achieved through conventional PWM which can be obtained from Arduino’s PWM output Pin 5 and 6. The enable/disable function of the mot..