Generic

The AC adapter, AC/DC adapter or AC/DC converter is a type of external power supply, often enclosed in a case similar to an AC plug. Other names include plug pack, plug-in adapter, adapter block, domestic mains adapter, line power adapter, wall wart, or power adapter; adapters for battery-powered eq..

An indicator light is mainly used on the circuit or mechanical equipment to monitor and alarm the operation status of the equipment. also LEDs are commonly used for indicator lights (such as power on/off lights) on electronic devices. They also have several other applications, including electronic s..

This is a Side Shaft DC metal gear motor having 1000 RPM. It is most suitable for medium weight robot running on average voltage. Motor runs smoothly from 9V to 12V and gives wide range of RPM, and torque.Features of 1000 RPM Side Shaft Gear DC Motor:6mm shaft diameter with internal hole.125gm weigh..

The TIP127 is a PNP Epitaxial Darlington Transistor. Mainly used for Medium Power Linear Switching Applications and Complements to TIP120/121/122.Features of TIP 127Collector-Emitter Volt (Vceo): 100V.Collector-Base Volt (Vcbo): 100V.Collector Current (Ic): 5.0A.hfe: 1,000 @ 500mA.Power Dissipation ..

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

A crystal oscillator is an electronic oscillator circuit that uses the mechanical resonance of a vibrating crystal of piezoelectric material to create an electrical signal with a very precise frequency.Features of 20 MHz Crystal Oscillators:Stability in frequency.Small in size.Low cost.Easy of inter..

The 28 Pin IC Socket-5Pc or 28 pin IC base acts as a removable 28 pin IC holder that can be soldered directly to the PCB while the IC remains interchangeable. Required for sensitive ICs which are temperature sensitive and cannot be soldered to the board or at places where the IC needs to be replaced..

The polyester film capacitor is a non-polarized capacitor used to store charge in it in the form of an electrostatic field.Features of 2.7nF/ 0.0027uF/100V 2A272J Polyester Film Capacitor:Capacitance: 2.7nF/ 0.0027uF.Voltage: 100 volt.Code: 2A272J.Type: polyester film.Applications of 2.7nF/ 0.0027uF..

This is a low cost low voltage durable Dual Shaft Plastic Gear BO Motor having 75 RPM. It is most suitable for light weight robot running on small voltage. Out of its two shafts one shaft can be connected to wheel, other can be connected to the position encoder. Drive shaft has clutch for non contin..

The DC motor is an electrical device which converts from dc electrical energy into mechanical energy.Features of 2400 RPM DC Motor:Low cost for control achieved.Low torque at startup and high speeds.Rugged design.Simplicity of construction.Can operate in an open loop control system.Low maintenance.L..

Features of 3000 Science Experiment Kit Gen 2 :In The Box – Package includes 1 battery base, 1 electrical machinery, 1 air blade, 1 small light bulb, 1 base, 1 battery, 2 alligator clip, 1 switch, 1 10cm line, 1 nail, 1 copper wire, 3 paper clip, 1 motor - Please Note Random Color Box Will Be D..

..

This is a Case B SMD Tantalum Capacitor of 47uf capacitance with rated voltage 16V.Specifications:Type: Tantalum CapacitorApplication: General PurposePackage Type: Surface MountCapacitance: 47uFRated Voltage: 16VOperating Temperature: -55oC -- +125oCPackage includes:10 x 47µF 16v SMD Capacitor..

These are 0805 size SMD Resistor with 1% tolerance. All thick film types of chip resistors have a rectangular ceramic body. The resistive element is a metal glaze film. The chips have been trimmed to the required ohmic resistance by cutting one or more grooves in the resistive layer. This process i..

..

This is a 26 pin dual row IDC female socket connector with central lug and strain-relief socket very suitable for the ribbon cable. These IDC sockets mate to standard 0.1" PCB Header pins or male IDC plugs. It is very easy to assemble IDC Termination for the standard ribbon cable.Specifications:Curr..

NFC Module Kit for Raspberry PiITEAD PN532 NFC module, as its name implies, is based on PN532 chip and used for 13.56MHz near field communication. The module is equipped with onboard antenna, thus no external antenna coil is needed. It is compatible with SPI, IIC and UART interface for communication..

The KK2.1.5 is next big evolution of the first generation KK flight control boards. The KK2.1.5 was engineered from the ground up to bring multi-rotor flight to everyone, not just the experts. The LCD screen and built in software makes install and setup easier than ever. A host of multi-rotor craft ..

The LilyPad Arduino is a microcontroller board designed for wearable and e-textiles. It can be sewn to fabric and similarly mounted power supplies, sensors and actuators with conductive thread. The board is based on the ATmega168V (the low-power version of the ATmega168). The LilyPad Arduino can be ..