Generic

ISD1820 Voice Recording module board is based on ISD18B20, which is a single-chip single-message record/playback device. Recordings are stored into on-chip non-volatile memory, providing Zero-power message storage. With the embedded Flash memory employed, data retention up to 100 years and typical 1..

15 Amp Cartridge Miniature Fuse is a 5mm x 20mm cartridge type Glass fuse which is user replaceable and provides reliable overload and short circuit protection.Features of 15 Amp Cartridge Miniature Fuse (5X20mm):Fast-acting, low breaking capacity.Optional axial leads available.5mm x 20mm physical s..

This DC female socket is a PCB mountable version of the Female DC socket. The rust-free contacts provide zero power loss and problem free operation.Features of DC Socket(PCB Mountable).High Quality Plastic material.Rust free material.Applications of DC Socket(PCB Mountable).External Power supply con..

A DIP switch is a manual electric switch that is packaged with others in a group in a standard dual in-line package (DIP) and can be used as 8-bit address switch.Features of 8 Ways DIP Switch / 8 Ways Slide SwitchSturdy built Quality.Easy to use.8 Bit address selection.Standard pin spacing for ..

A DIP switch is a manual electric switch that is packaged with others in a group in a standard dual in-line package (DIP) and can be used as4-bit address switchFeatures of DIP Switch (4 bit):Sturdy built Quality.Easy to use.4 Bit address selection.Standard pin spacing for use in PCB and also bread b..

A DIP switch is a manual electric switch that is packaged with others in a group in a standard dual in-line package (DIP) and can be used as 2-bit address switchFeatures of DIP Switch (2 Bit):Sturdy built Quality.Easy to use.2 Bit address selection.Standard pin spacing for use in PCB and also bread ..

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

A 40 pin header (or simply header) is a form of electrical connector, often associated with ribbon cable connector. It consists of one or more rows of pins typically spaced 0.1 inches (2.54 mm) apart, but sometimes 2mm (0.079 in) or 0.05 inches (1.27 mm) is used as wellFeatures of 40 Pin Rectangle M..

A photoresistor or LDR 5mm - Light Dependent Resistor is a resistor whose resistance decreases with increasing incident light intensity; in other words, it exhibits photoconductivity.A photo-resistor is made of a high resistance semiconductor. If light falling on the device is of high enough frequen..

A light-emitting diode (LED) is a two-lead semiconductor light source. It is a p–n junction diode, which emits light when activated. When a suitable voltage is applied to the leads, electrons are able to recombine with electron holes within the device, releasing energy in the form of photons. This e..

An IR LED, also known as IR transmitter, is a special purpose LED that transmits infrared rays in the range of 760 nm wavelength. Such LEDs are usually made of gallium arsenide or aluminum gallium arsenide. They, along with IR receivers, are commonly used as infrared sensors.Features of IR LED Blue ..

This pressure sensor is a very high accuracy (1m) which converting from normal pressure into some digital serial data output. This boardusing a sensor as capable as the BMP180 you can achieve accuracy of 1m, with noise of only 17cm in ultra high resolution noise. The device will operate at only 0.3u..

The ESP8266 is a Wi-Fi module serial Transceiver used for wireless data communication. You can also say that WLAN transceiver. It is converting from wired LAN into wireless LAN (WLAN).Features of ESP8266 Wireless Module ESP-12E Serial Port Wi-Fi Module:This module requires a 3.3 volt supply for VCC,..

The push to on switch is a switch which turns on when it is push and off when it is pulled. A push-button (also spelled pushbutton) or simply button is a simple switch mechanism for controlling some aspect of a machine or a processFeatures of Push ON OFF Switch:Heavy strong plastic material.350 degr..

A screwdriver is a tool, manual or powered, for turning (driving or removing) screws. A typical simple screwdriver has a handle and a shaft, and a tip that the user inserts into the screw head to turn it. The shaft is usually made of tough steel to resist bending or twisting.Features of Screw Driver..

The Multipurpose PCB Board is a useful tool for developing prototypes for new projects and building a circuit from 0 level. Requires medium level of Circuit Construction Level Knowledge. The Board is a strong and clear epoxy type board with pre-drilled mounting holes. The oxide free surface allows e..

DESOLDERING is the process of removing soldered components from a circuit made on PCB. De-soldering pump along with the soldering iron is used for this purpose. A de-soldering pump also known as solder sucker is a small mechanical device which sucks the liquid/molten solder from the joint where the ..

The solder is a smooth wire combination of Tin and Lead (60% & 40%) used to make connection of wires, Electronic components etc.Features of Solder Wire (30 Gm):Halide-free solder wire, and suitable for repair operation.Used in tin-lead process.Fast melting, good wetting and expansibility.No bre..

This is a simple soldering iron stand composed of a heavy-duty metal base and a reinforced spring holder. The base and holder are detachable.Features of Iron Stand:Heavy strength.Effective heat transfer.Applications of Iron Stand:It is used in soldering work to keep heat soldering iron safety.Also S..

400KV Step Up Power ModuleThis is a high voltage step-up power supply module, which is commonly used in electronics experiments and demonstrations. The module can generate a voltage of up-to 400KV from an input of 3-6V from a normal Li-ion battery. The high-voltage module uses the principle of the T..