Generic

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

The Infrared Emitting Diode (IR333C) is a high intensity diode, molded in a water clear plastic package. The device is spectrally matched with phototransistor, photodiode and infrared receiver module.Features of IR LED 5 MM:High reliability.High radiant intensity.Peak wavelength λp=940nm.2.54mm Lead..

An IR LED, also known as IR transmitter, is a special purpose LED that transmits infrared rays in the range of 760 nm wavelength. Such LEDs are usually made of gallium arsenide or aluminum gallium arsenide. They, along with IR receivers, are commonly used as infrared sensors.Features of IR LED ..

The LM317 3-Terminal Adjustable Linear Voltage Regulator To-92 Package used in DC to DC converter applications. The overall function of the LM317 is similar to that of the LM78xx series regulators. Whereas the 78xx series of regulators have fixed output voltages (ex. 7805 has 5V output), the LM..

The FT232R USB UART Driver IC is a device which simplifies USB to serial designs and reduces external component count by fully integrating an external EEPROM, USB termination resistors and an integrated clock circuit which requires no external crystal, into the device. It has been designed to operat..

IRGB430U MOSFET - 500V 15A N- Channel Power MOSFET TO-220 PackageInsulated  Gate  Bipolar  Transistors  (IGBTs)  from  International  Rectifier  have higher  usable  current  densities  than  comparable  bipolar  transistors,..

400KV Step Up Power ModuleThis is a high voltage step-up power supply module, which is commonly used in electronics experiments and demonstrations. The module can generate a voltage of up-to 400KV from an input of 3-6V from a normal Li-ion battery. The high-voltage module uses the principle of the T..

The 74ls08 quad 2 input and gates contains four independent gates each of which performs the logic AND function. 74ls08 quad 2 input and gate IC can be soldered directly to the circuit board or can be mounted on a 14 pin IC base. The 74ls08 quad 2 input and gates circuit is designed such that the AN..

The high-performance, low-power Atmel 8-bit AVR RISC-based microcontroller combines 16KB ISP flash memory, 1KB SRAM, 512B EEPROM, an 8-channel/10-bit A/D converter (TQFP and QFN/MLF), and debugWIRE for on-chip debugging. The device supports a throughput of 20 MIPS at 20 MHz and operates between 2.7-..

74LS28 Quad 2-Input NOR contains four independent 2 input gates each of which performs the logic NOR function74LS28 IC can be soldered directly to the circuit board or can be mounted on a 14 pin IC base. 74LS28 Quad 2-Input NOR Buffer circuit is designed such that the NOR operation produced on the i..

This DC female socket is a PCB mountable version of the Female DC socket. The rust-free contacts provide zero power loss and problem free operation.Features of DC Socket(PCB Mountable).High Quality Plastic material.Rust free material.Applications of DC Socket(PCB Mountable).External Power supply con..

A light-emitting diode (LED) is a two-lead semiconductor light source. It is a p–n junction diode, which emits light when activated. When a suitable voltage is applied to the leads, electrons are able to recombine with electron holes within the device, releasing energy in the form of photons. This e..

A light-emitting diode (LED) is a two-lead semiconductor light source. It is a p–n junction diode, which emits light when activated. When a suitable voltage is applied to the leads, electrons are able to recombine with electron holes within the device, releasing energy in the form of photons. This e..

An IR LED, also known as IR transmitter, is a special purpose LED that transmits infrared rays in the range of 760 nm wavelength. Such LEDs are usually made of gallium arsenide or aluminum gallium arsenide. They, along with IR receivers, are commonly used as infrared sensors.Features of IR LED Blue ..

A photoresistor or LDR 5mm - Light Dependent Resistor is a resistor whose resistance decreases with increasing incident light intensity; in other words, it exhibits photoconductivity.A photo-resistor is made of a high resistance semiconductor. If light falling on the device is of high enough frequen..

Laser Diode Modules are used in a variety of applications that require small sizes in addition to low power consumption with long operating lifetimes. Laser Diode Modules are lasers lab or OEM integration. Laser Diode Modules are ideal for applications such as life science, industrial, or scientific..

A DIP switch is a manual electric switch that is packaged with others in a group in a standard dual in-line package (DIP) and can be used as4-bit address switchFeatures of DIP Switch (4 bit):Sturdy built Quality.Easy to use.4 Bit address selection.Standard pin spacing for use in PCB and also bread b..