Search

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

A DIP switch is a manual electric switch that is packaged with others in a group in a standard dual in-line package (DIP) and can be used as 2-bit address switchFeatures of DIP Switch (2 Bit):Sturdy built Quality.Easy to use.2 Bit address selection.Standard pin spacing for use in PCB and also bread ..

The 74ls08 quad 2 input and gates contains four independent gates each of which performs the logic AND function. 74ls08 quad 2 input and gate IC can be soldered directly to the circuit board or can be mounted on a 14 pin IC base. The 74ls08 quad 2 input and gates circuit is designed such that the AN..

74LS28 Quad 2-Input NOR contains four independent 2 input gates each of which performs the logic NOR function74LS28 IC can be soldered directly to the circuit board or can be mounted on a 14 pin IC base. 74LS28 Quad 2-Input NOR Buffer circuit is designed such that the NOR operation produced on the i..

L7806/LM7806 Voltage Regulator is a 6V voltage regulator that can provide local on-card regulation, eliminating the distribution problems associated with single point regulation. Each type employs internal current limiting, thermal shut-down and safe area protection, making it essentially indestruct..

74LS161 Synchronous 4-Bit Counter contains high-speed 4-bit synchronous counters. They are edge-triggered, synchronously presettable, and cascadable MSI building blocks for counting, memory addressing, frequency division and other applications. 74LS161 IC can be soldered directly to the circuit boar..

The 74LS11 Triple 3-Input AND Gatecontains three independent gates each of which performs the logic AND function. 74LS11 Triple 3-Input AND Gate IC can be soldered directly to the circuit board or can be mounted on a 14 pin IC base. 74LS11 Triple 3-Input AND Gate circuit is designed such that the AN..

74LS75 4-Bit Bi-Stable Latch contains latches are ideally suited for use as temporary storage for binary information between processing units and input/output or indicator units. Information present at a data (D) input is transferred to the Q output when the enable is HIGH, and the Q output will fol..

The 74LS12 Triple 3-Input Positive NAND Gates With Collector Outputs contains three 3 input independent gates each of which performs the positive logic NAND function. 74LS12 IC can be soldered directly to the circuit board or can be mounted on a 14 pin IC base. 74LS12 Triple 3-Input Positive NAND Ga..

The 74LS10 Triple-3-Input NAND Gate contains three independent gates each of which performs the logic AND function. 74LS10 Triple-3-Input NAND Gate IC can be soldered directly to the circuit board or can be mounted on a 14 pin IC base. The 74LS10 Triple-3-Input NAND Gate circuit is designed such tha..

The 212 encoders are a series of CMOS LSI'S for remote control system applications. They are capable of encoding information which consists of N address bits and 12N data bits. Each address/data input can be set to one of the two logic states. The programmed addresses/data are transmitted together w..

74LS86 Quad 2 Input Exclusive OR Gate contains four independent gates each of which performs the logic XOR function. 74LS86 Quad 2 Input Exclusive OR Gate circuit is designed such that the OR operation of the input pins 1,2 , 4,5, 9,10 & 12,13 are produced on the pin 3, 6, 8 & 11 respectivel..

This 1 Amp Cartridge Miniature Fuse (6mmx31mm) is a fast acting glass tube cartridge fuse. It is an electrical safety device that operates to provide overcurrent protection of an electrical circuit. Its essential component is a zinc wire or strip that melts when too much current flows through it. Th..

TOP271EG – POWER INTEGRATIFeatures:IC Name: TOP271EGPackage/Case: SIP-7..

The RS232 Tester can be connected across any Serial PORT (at a SUB-D9 interface) to visually monitor the outputs on LED and set any input signals through switches. The tester is installed at an existing serial connection and offers easy testing as well as a loop-back connection test.It has male head..

TPS54231DR – 3.5-28V 2A 570kHz Adjustable Output Step-Down Converter Eco-mode ICFeatures:IC Name: TPS54231DRPackage/Case: SMD-8..

A resistor is a passive two-terminal electrical component that implements electrical resistance as a circuit element. Resistors act to reduce current flow, and, at the same time, act to lower voltage levels within circuits. In electronic circuits, resistors are used to limit current flow, to adjust ..

This is a MQ6 gas sensor breakout module used for interfacing of MQ6 sensor.Features of Gas Sensor Breakout Board:High Sensitivity to LPG, ISO-butane, propane.Small sensitivity to alcohol, smoke.Detection Range: 100 - 10,000 ppm ISO-butane propane.Fast Response Time: < 10s.Simple drive circuit.He..

The Arduino Prototyping Shield makes it easy for you to design custom circuits. You can solder parts to the prototyping area to create your project, or use it with a small solderless breadboard (not included) to quickly test circuit ideas without having to solder.Specification of Arduino Prototyping..