Generic

The AC adapter, AC/DC adapter or AC/DC converter is a type of external power supply, often enclosed in a case similar to an AC plug. Other names include plug pack, plug-in adapter, adapter block, domestic mains adapter, line power adapter, wall wart, or power adapter; adapters for battery-powered eq..

DESOLDERING is the process of removing soldered components from a circuit made on PCB. De-soldering pump along with the soldering iron is used for this purpose. A de-soldering pump also known as solder sucker is a small mechanical device which sucks the liquid/molten solder from the joint where the ..

A screwdriver is a tool, manual or powered, for turning (driving or removing) screws. A typical simple screwdriver has a handle and a shaft, and a tip that the user inserts into the screw head to turn it. The shaft is usually made of tough steel to resist bending or twisting.Features of Screw Driver..

A 40 pin header (or simply header) is a form of electrical connector, often associated with ribbon cable connector. It consists of one or more rows of pins typically spaced 0.1 inches (2.54 mm) apart, but sometimes 2mm (0.079 in) or 0.05 inches (1.27 mm) is used as wellFeatures of 40 Pin Rectangle M..

USB to TTL Bridge is the easiest method to connect USB to TTL signal to PC via USB ideal for microcontroller board. The control circuit for the module is based on PL2303 circuit which makes it a full duplex USB to TTL converter. The PL-2303 operates as a bridge between one USB port and one standard ..

The ATMEL 89C2051 Microcontroller or commonly known as AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the industry-sta..

L298 is an integrated monolithic circuit in a 15 - lead Multiwatt and PowerSO20 packages. It is a high voltage, high current dual full-bridge driver designed to accept standard TTL logic levels and drive inductive loads such as relays, solenoids, DC and stepping motors. Two enable inputs are provide..

The ESP8266 is a Wi-Fi module serial Transceiver used for wireless data communication. You can also say that WLAN transceiver. It is converting from wired LAN into wireless LAN (WLAN).Features of ESP8266 Wireless Module ESP-12E Serial Port Wi-Fi Module:This module requires a 3.3 volt supply for VCC,..

A DIP switch is a manual electric switch that is packaged with others in a group in a standard dual in-line package (DIP) and can be used as 2-bit address switchFeatures of DIP Switch (2 Bit):Sturdy built Quality.Easy to use.2 Bit address selection.Standard pin spacing for use in PCB and also bread ..

The solder is a smooth wire combination of Tin and Lead (60% & 40%) used to make connection of wires, Electronic components etc.Features of Solder Wire (30 Gm):Halide-free solder wire, and suitable for repair operation.Used in tin-lead process.Fast melting, good wetting and expansibility.No bre..

The 74LS00 IC is a Quad 2 Input NAND Gate which is 14 pin IC used to perform NAND operation of digital data. This IC has 4 independent NAND gate with 14 no. pin Vcc and 7 no. pin Gnd, pin no. 1 & 2 input and pin no. 3 is output, pin no. 4 & 5 input and 6 is output, 8 & 9 input & 10 i..

You know those ZIF sockets we have for DIP chips? Well these are just like that but for SMT parts! Yeah, that's right, now you can program and test out your favorite new parts in TQFP-32 packages. This test sockets is good for any QFP-32 in a 7mm square body. Simply open the latch, place the chip in..

18-0-18 1A Center Tapped Step Down Transformer is a general-purpose chassis mounting mains transformer. The transformer has 230V primary winding and center-tapped secondary winding. The transformer has flying-colored insulated connecting leads ( Approx 100 mm long ). The Transformer act as step-down..

About this itemDimension 11 x 11 x 5.3 mm, Perfect fit for Raspberry Pi Zero / Raspberry Pi Zero WPremium Quality Anodized AluminumThermal resistance 31§C/W (large-black) at 200 LFMComes with 3M double sided adhesivePackage Content: 1 Pack..

UDH SH 124D 24V 7A 5Pin RelayFeatures of UDH SH 124D 24V 7A 5Pin Relay :Single contact Form (SPST) series Relay offers switching capacity 30A in small size.Dust cover, sealed & unclosed cover types are available.UL Class F insulation available.Halogen Free series available.Comply with&..

A cable tie, also known as a hose tie, or zip tie or tie-wrap, is a type of fastener, designed for bunching electric cables or wires and to organize cables and wires, but with a wide variety of other applications.Features of Zip Tie Pack:Ease of holding substance.One time use.Length - 12 inch A..

A cable tie, also known as a hose tie, or zip tie or tie-wrap, is a type of fastener, designed for bunching electric cables or wires and to organize cables and wires, but with a wide variety of other applications.Features of Zip Tie Pack:Ease of holding substance.One time use.Length - 8 inch Ap..

A cable tie, also known as a hose tie, or zip tie or tie-wrap, is a type of fastener, designed for bunching electric cables or wires and to organize cables and wires, but with a wide variety of other applications.Features of Zip Tie Pack:Ease of holding substance.One time use.Length - 8 inch Ap..

A cable tie, also known as a hose tie, or zip tie or tie-wrap, is a type of fastener, designed for bunching electric cables or wires and to organize cables and wires, but with a wide variety of other applications.Features of Zip Tie Pack:Ease of holding substance.One time use.Length - 3 inch Ap..

A cable tie, also known as a hose tie, or zip tie or tie-wrap, is a type of fastener, designed for bunching electric cables or wires and to organize cables and wires, but with a wide variety of other applications.Features of Zip Tie Pack:Ease of holding substance.One time use.Length - 4 inch Ap..